A coupling is a part that connects two different rotating bodies (motor shaft, ball screw, etc.) and aims at transmitting torque. The load of assembly adjustment is reduced by absorbing the axis deviation (lateral misalignment, angular misalignment and axial amplitude) between rotating bodies. And in case of accidental overload, the coupling is destroyed and the rotating bodies are disconnected to protect the expensive power part and the whole device.

What are the types of MISUMI couplings?

There are disc type, grooved type, cross type, claw type, bellows type, rigid type and universal joint type.

How to select coupling according to motor?

Disc type is recommended for servo motors, grooved type is recommended for stepping motors, and cross type is recommended for universal motors.

How to select according to the purpose, environment, working conditions?

Please refer to the MISUMI website.

What kind of coupling should be used when the angular misalignment is very large?

Please select the universal joint with allowable angular misalignment of 30 degrees. In addition, when grease cannot be applied regularly, use a rubber sleeve to fill grease and use it.

Which disc type coupling is better, single disc type or double disc type?

Double disc type can absorb angular misalignment and lateral misalignment, but the total length will increase. Although the total length of the single disc type is short, it is only suitable for applications with narrow space because lateral misalignment is not allowed in the structure. Special attention should be paid to centering during use.

How much is appropriate to insert the shaft into the coupling during installation?

Please select the length of the main body (coupling part) described in the product catalog. If the insertion amount is too short, the shaft may slip and the clamping part may be damaged; If the insertion amount is too long, it will be damaged due to shaft interference inside the coupling.

Why is it necessary to install a protection cover around the coupling?

Due to high-speed rotation, accidental contact may result in injury or entanglement of gloves, towels, etc. In addition, for some reasons, parts may be damaged or debris may be scattered. Therefore, be sure to install the safety protection cover.

What should I do if there is no matching shaft bore diameter?

Please select a product with changeable keyway width or available with keyway processing. MISUMI products are divided into MCSLCWK series (disc type), CPOC series (cross type) and MMJN series (claw type), etc.

Is it a defective product that has difference in groove gap width?

Since the difference is within the dimensional tolerance range, there is no problem.

(!)Due to Microsoft's end of support for Internet Explorer 11 on 15/06/2022, this site does not support the recommended environment.

MISUMI

Webcode Seach | Series: #CODE

Keyword suggestions

Part number suggestions

Discontinued Products

This translation is a Google translation Dịch tự động bởi Google 이 번역은 Google 번역입니다 此翻译是Google翻译此翻譯是Google翻譯

[Thông báo] Sử Dụng Địa Chỉ Hành Chính Mới Cho Giao/Nhận Hàng Hóa Từ 1/10/2025. Xem chi tiết.
[Notice] Update of Official Address for Delivery and Receipt of Goods from October 1, 2025. See more.
[Cảnh Báo] Thủ Đoạn Lừa Đảo Từ Nhân Viên Giao Hàng - Yêu Cầu Trả Phí Ship. Xem chi tiết
[Warning] Fraud Calling from Shipper - Asking to Pay Shipping Fee. See more

How can we improve?

How can we improve?

Comments

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Customer Privacy Policy

Thank you for your cooperation.

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Please use the inquiry form.

Customer Privacy Policy

ConfigureTạo

Part number has not been determine

(39 Part Numbers Available)

Configure Remaining SpecificationsĐịnh cấu hình các thông số còn lại

Part Number CompleteĐã hoàn thành

GSASL8-3-3

Shaft Bore Dia. 1 d1 (or d) Shaft Bore Dia. 2 d2 (or d) O.D. Overall Length Allowable Torque Range Allowable Torque Allowable Lateral Misalignment Shaft Tightening Method type CAD Days to Ship

Specification/DimensionsĐặc điểm kỹ thuật / Kích thướcĐặc điểm kỹ thuật / Kích thước

Shaft Bore Dia. 1 d1 (or d)(Ø)
3

4

5

6

6.35

8

10

12
ClearTrống
Shaft Bore Dia. 2 d2 (or d)(Ø)
3

4

5

6

6.35

8

10

11

12

14
ClearTrống
O.D.(Ø)
8

12

16

20

25

32
ClearTrống
Overall Length(mm)
14

18.5

23

26

31

41
ClearTrống
Allowable Torque Range(N•m)
0.05~1.00

1.01~3.00

3.01~5.00
ClearTrống
Allowable Torque(N•m)
0.1

0.4

0.5

1

2

4
ClearTrống
Allowable Lateral Misalignment(mm)
0.1

0.15
ClearTrống
Shaft Tightening Method
- 止动螺丝
ClearTrống
type
- GSASL
ClearTrống
CADCAD
- 2D
- 3D
ClearTrống

Days to ShipSố ngày giao hàng

Alltất cả các

Same day

6 Day(s) or Less

8 Day(s) or Less

10 Day(s) or Less

16 Day(s) or Less

27 Day(s) or Less
ClearTrống

Specify AlterationsChỉ định thay đổi

Slit Couplings Long, Set Screw Type

Click this image to zoom it.Nhấp vào hình ảnh này để phóng to.

Move the mouse over or click the image to zoom

Volume Discount

Check FAQ of this product (10 items)

Brand :

MiSUMi Economy

Part Number :

GSASL8-3-3

GSASL12-3-3

GSASL12-3-4

GSASL12-3-5

GSASL12-4-4

GSASL12-4-5

GSASL12-5-5

GSASL12-5-6

GSASL16-4-4

GSASL16-4-5

GSASL16-5-5

GSASL16-5-8

GSASL16-6-6

GSASL20-5-5

GSASL20-5-6

GSASL20-5-8

GSASL20-6-6

GSASL20-6-6.35

GSASL20-6-8

GSASL20-6-10

GSASL8-3-3

Order Qty :
Total Price :

---
Days to ship :

---

Select part number to Order Now/ Add to Cart

CAD Download

(i)
Caution

thận trọng

**RoHS Compliant is available for some part numbers.
Please contact with MISUMI for detail effective date.

Product Description

This is an economy item, The price is cheaper than the MISUMI standard product.

[Features/Characteristics]
The metal elastic coupling is integrally formed with zero rotary clearance. Elastic action compensates radial, angular and axial deviations. Clockwise and counterclockwise rotary characteristics are identical.

Economy Long Slit Coupling - Set Screw Type

High rigidity Angular deviation Easy installation

- Superior aluminum alloy construction provides high durability

- Integrally formed metal elastic coupling with zero rotary clearance

- Compensates for radial, angular, and axial deviations, ensuring smooth operation

- Clockwise and counterclockwise rotary characteristics are identical

- Set screw fixing type allows for secure and easy installation

Economy Long Slit Coupling - Set Screw Type

MISUMI Standard

Cheaper Price

Product Variety

3D CAD
3D CAD Support

Coupling Product Overview

The parallel line coupling takes into account the shortening of slots without weakening the ability to bear and correct deviation. Short slots can enhance and overlap the torque rigidity of the coupling, so that it can bear considerable torque.
The parallel line coupling usually has 3 to 5 slots to deal with the problem of low torque rigidity.
The parallel line coupling takes into account the shortening of slots without weakening the ability to bear and correct deviation. Short slots can enhance and overlap the torque rigidity of the coupling, so that it can bear considerable torque.

Coupling Product Feature

【Features/Characteristics】The metal elastic coupling is integrally formed with zero rotary clearance. Elastic action compensates radial, angular and axial deviations. Clockwise and counterclockwise rotary characteristics are identical. Positioning screw fixing. Aluminum alloy material
【Usage】Suitable for standard motors
【Precautions】Moment of inertia and weight are calculated at the maximum shaft dia.
【Type】Grooved type
【Body Material】Aluminum alloy
【Fixing System】Set Screw fixing type
【Applicable Motors】Servo motors and stepping motors
■ Parallel line couplings are suitable for light load applications.

Dimensional Coupling Drawing

【Economic type】Grooved coupling Set screw type Length-increased type: Related image

TYPE	[M]Material	[ S ] Surface Treatment	[ A ] Accessories
GSASL	Aluminum	Alumite Treatment	Set Screw

Coupling Specification Table

Please order after selecting part number and parameters according to the selection steps to . 【Economic type】Grooved coupling Set screw type Length-increased type: Related image

Part Number (Type· D)	－	d₁	－	d₂
GSASL20	－	6	－	8

Part Number		d₁	d₂											L	ℓ	Set Screw		F
Type	D	d₁	d₂											L	ℓ	M (Coarse Thread)	Tightening torque (N·m)	F
Set Screw GSASL	8	2	2	3										14	3.5	M3	0.3	1.7
	8	3		3										14	3.5	M3	0.3	1.7
	12	3		3	4	5								18.5	2.5	M2.5	0.5	5
		4			4	5
		5				5	6
	16	4			4	5	6							23	6.4	M3	0.7	3
		5				5	6		8
		6					6		8
	20	5				5	6		8					26	7
		6					6	6.35	8	10
		6.35							8
		8							8	10
		10								10
	25	6					6		8	10				31	8	M4	1.7	4
		6.35							8	10
		8							8	10		12
		9.525								10
		10								10		12
	32													41	11			6
		8							8			12
		10								10	11	12	14
		12										12	14

■Characteristic Value

Part Number		Allowable torque (N·m)	Maximum rotational speed (rpm)	Moment of inertia (kg·m²)	Static torsional stiffness (N·m/rad)	Allowable lateral misalignment (mm)	Allowable Angular Misalignment ( ° )	Allowable axial amplitude (mm)	Weight (g)
Type	D	Allowable torque (N·m)	Maximum rotational speed (rpm)	Moment of inertia (kg·m²)	Static torsional stiffness (N·m/rad)	Allowable lateral misalignment (mm)	Allowable Angular Misalignment ( ° )	Allowable axial amplitude (mm)	Weight (g)
GSASL	8	0.1	10,000	1.2×10^－8	25	0.1	2	±0.2	4.5
	12	0.4		8.3×10^－8	45			±0.3	6
	16	0.5		6.5×10^－7	44			±0.4	9
	20	1		1.5×10^－6	110			±0.4	16
	25	2		4.2×10^－6	215	0.15		±0.5	27
	32	4		1.6×10^－5	420	0.15			64
	40	8		3.2×10^－5	700	0.2			134

[ ! ]Static torsional stiffness, moment of inertia and weight are the values at the maximum shaft dia..

Coupling Precautions

■ Calibration and adjustment
1. The coupling allows axis deviation, and transmits rotation angle and torque, but when the axis deviation exceeds the allowable value, vibration will occur or the service life will be drastically reduced.
Be sure to make calibration and adjustment.
2. Axis deviation includes lateral misalignment (parallel error of two axes), angular misalignment (angular error of two axes) and axial amplitude (axial movement of shaft).
Please calibrate and adjust the shaft to ensure that the axis deviation is below the allowable value recorded in the dimension and performance table of each product.
3. The allowable value of axis deviation recorded in the dimension and performance table refers to the situation when either lateral misalignment, angular misalignment or axial amplitude occurs alone. When more than two axis deviations occur at the same time, the corresponding allowable values are halved respectively.
4. Axis deviation not only occurs when assembling to the device, but also is caused by vibration, thermal expansion and bearing wear in operation. Therefore, it is recommended to set the axis deviation below 1/3 of the allowable value.

Example of Use coupling


Use example of coupling 1: motor×gear box	Use example of coupling 2: motor×ball screw


Use example of coupling 3: motor×encoder	Use example of coupling 2 motor×measuring tester

Coupling Usage Method

■Mounting method
STEP1 Insert the coupling
Confirm that the clamping bolt has been unscrewed, and then remove the dust, foreign matter and oil from the shaft and coupling bore.
Then, when inserting the coupling into the shaft, please be careful not to put the disc under excessive stress such as compression or tension.
STEP2 Use fixture to adjust
Please use fixture to adjust and fix the concentricity of the left and right hubs of the coupling with high accuracy.
STEP3 Simple lateral misalignment and angular misalignment confirmation
Under the condition of unscrewed bolts, make the coupling slide axially and confirm its smooth movement.
Then, rotate the coupling to make sure it moves smoothly.
Lateral misalignment is not allowed for single disc type coupling, so carry out positioning securely.
Simple lateral misalignment confirmation

Simple lateral misalignment confirmation

Simple angular misalignment confirmation

STEP4 Installation
Please adjust the shaft insertion amount according to the dimension ℓ in the product catalog, and use a torque wrench to tighten with the specified torque.
＊ If the specified torque cannot be reached once, please cross fasten the left and right clamps twice or three times.

Part Number

Incomplete part number.
Please use left hand selections to complete a part number.Incomplete part number.
Please use left hand selections to complete a part number.

Loading...Tải…

: 30; 45; 60

Part Number
GSASL8-3-3
GSASL12-3-3
GSASL12-3-4
GSASL12-3-5
GSASL12-4-4
GSASL12-4-5
GSASL12-5-5
GSASL12-5-6
GSASL16-4-4
GSASL16-4-5
GSASL16-5-5
GSASL16-5-8
GSASL16-6-6
GSASL20-5-5
GSASL20-5-6
GSASL20-5-8
GSASL20-6-6
GSASL20-6-6.35
GSASL20-6-8
GSASL20-6-10
GSASL20-6.35-8
GSASL20-8-10
GSASL25-6-8
GSASL25-6-10
GSASL25-6.35-8
GSASL25-6.35-10
GSASL25-8-8
GSASL25-8-10
GSASL25-8-12
GSASL25-10-10
GSASL25-10-12
GSASL32-8-8
GSASL32-8-12
GSASL32-10-10
GSASL32-10-11
GSASL32-10-12
GSASL32-10-14
GSASL32-12-12
GSASL32-12-14

Price	Minimum Order Qty.	Volume Discount	Days to ShipSố ngày giao hàng	Shaft Bore Dia. 1 d1 (or d) (Ø)	Shaft Bore Dia. 2 d2 (or d) (Ø)	O.D. (Ø)	Overall Length (mm)	Allowable Torque Range (N•m)	Allowable Torque (N•m)	Allowable Lateral Misalignment (mm)	Allowable Axial Misalignment (mm)	Moment of Inertia (kg・m2)	Shaft Tightening Method
161,851 VND	1 Piece(s)	Available	8 Day(s)	3	3	8	14	0.05~1.00	0.1	0.1	0.2	1.2×10^-8	止动螺丝
160,952 VND	1 Piece(s)	Available	10 Day(s)	3	3	12	18.5	0.05~1.00	0.4	0.1	0.3	8.3×10^-8	止动螺丝
160,952 VND	1 Piece(s)	Available	10 Day(s)	3	4	12	18.5	0.05~1.00	0.4	0.1	0.3	8.3×10^-8	止动螺丝
160,950 VND	1 Piece(s)	Available	Same day	3	5	12	18.5	0.05~1.00	0.4	0.1	0.3	8.3×10^-8	止动螺丝
160,950 VND	1 Piece(s)	Available	6 Day(s)	4	4	12	18.5	0.05~1.00	0.4	0.1	0.3	8.3×10^-8	止动螺丝
167,251 VND	1 Piece(s)	Available	16 Day(s)	4	5	12	18.5	0.05~1.00	0.4	0.1	0.3	8.3×10^-8	止动螺丝
160,950 VND	1 Piece(s)	Available	Same day	5	5	12	18.5	0.05~1.00	0.4	0.1	0.3	8.3×10^-8	止动螺丝
160,950 VND	1 Piece(s)	Available	Same day	5	6	12	18.5	0.05~1.00	0.4	0.1	0.3	8.3×10^-8	止动螺丝
167,273 VND	1 Piece(s)	Available	Same day	4	4	16	23	0.05~1.00	0.5	0.1	0.4	6.5 x 10^-7	-
119,108 VND	1 Piece(s)	Available	6 Day(s)	4	5	16	23	0.05~1.00	0.5	0.1	0.4	6.5 x 10^-7	-
167,273 VND	1 Piece(s)	Available	Same day	5	5	16	23	0.05~1.00	0.5	0.1	0.4	6.5 x 10^-7	-
167,269 VND	1 Piece(s)	Available	Same day	5	8	16	23	0.05~1.00	0.5	0.1	0.4	6.5 x 10^-7	-
164,157 VND	1 Piece(s)	Available	Same day	6	6	16	23	0.05~1.00	0.5	0.1	0.4	6.5×10^-7	止动螺丝
175,576 VND	1 Piece(s)	Available	10 Day(s)	5	5	20	26	0.05~1.00	1	0.1	0.4	1.5×10^-6	止动螺丝
168,057 VND	1 Piece(s)	Available	Same day	5	6	20	26	0.05~1.00	1	0.1	0.4	1.5 x 10^-6	-
168,054 VND	1 Piece(s)	Available	Same day	5	8	20	26	1.01~3.00	1	0.1	0.4	1.5 x 10^-6	-
168,057 VND	1 Piece(s)	Available	Same day	6	6	20	26	0.05~1.00	1	0.1	0.4	1.5 x 10^-6	-
168,057 VND	1 Piece(s)	Available	Same day	6	6.35	20	26	0.05~1.00	1	0.1	0.4	1.5×10^-6	止动螺丝
168,054 VND	1 Piece(s)	Available	Same day	6	8	20	26	0.05~1.00	1	0.1	0.4	1.5 x 10^-6	-
168,048 VND	1 Piece(s)	Available	Same day	6	10	20	26	0.05~1.00	1	0.1	0.4	1.5 x 10^-6	-
175,568 VND	1 Piece(s)	Available	Same day	6.35	8	20	26	0.05~1.00	1	0.1	0.4	1.5×10^-6	止动螺丝
175,568 VND	1 Piece(s)	Available	Same day	8	10	20	26	0.05~1.00	1	0.1	0.4	1.5×10^-6	止动螺丝
210,545 VND	50 Piece(s)		16 Day(s)	6	8	25	31	1.01~3.00	2	0.15	0.5	4.2×10^-6	止动螺丝
213,497 VND	1 Piece(s)	Available	Same day	6	10	25	31	1.01~3.00	2	0.15	0.5 / +0.5/-0.5	4.2 x 10^-6	-
213,497 VND	1 Piece(s)	Available	Same day	6.35	8	25	31	1.01~3.00	2	0.15	0.5 / +0.5/-0.5	4.2 x 10^-6	-
213,497 VND	1 Piece(s)	Available	Same day	6.35	10	25	31	1.01~3.00	2	0.15	0.5 / +0.5/-0.5	4.2 x 10^-6	-
213,497 VND	1 Piece(s)	Available	Same day	8	8	25	31	1.01~3.00	2	0.15	0.5 / +0.5/-0.5	4.2 x 10^-6	-
213,494 VND	1 Piece(s)	Available	Same day	8	10	25	31	1.01~3.00	2	0.15	0.5 / +0.5/-0.5	4.2 x 10^-6	-
213,487 VND	1 Piece(s)	Available	Same day	8	12	25	31	0.05~1.00	2	0.15	0.5 / +0.5/-0.5	4.2 x 10^-6	-
210,536 VND	1 Piece(s)	Available	Same day	10	10	25	31	1.01~3.00	2	0.15	0.5	4.2×10^-6	止动螺丝
210,531 VND	1 Piece(s)	Available	Same day	10	12	25	31	1.01~3.00	2	0.15	0.5	4.2×10^-6	止动螺丝
327,592 VND	1 Piece(s)	Available	16 Day(s)	8	8	32	41	3.01~5.00	4	0.15	0.5	1.6×10^-5	止动螺丝
327,578 VND	1 Piece(s)	Available	Same day	8	12	32	41	3.01~5.00	4	0.15	0.5	1.6×10^-5	止动螺丝
330,989 VND	1 Piece(s)	Available	Same day	10	10	32	41	3.01~5.00	4	0.15	0.5 / +0.5/-0.5	1.6 x 10^-5	-
328,696 VND	1 Piece(s)	Available	27 Day(s)	10	11	32	41	3.01~5.00	4	0.15	0.5 / +0.5/-0.5	1.6 x 10^-5	-
331,167 VND	1 Piece(s)	Available	Same day	10	12	32	41	3.01~5.00	4	0.15	0.5 / +0.5/-0.5	1.6 x 10^-5	-
330,987 VND	1 Piece(s)	Available	Same day	10	14	32	41	3.01~5.00	4	0.15	0.5 / +0.5/-0.5	1.6 x 10^-5	-
330,989 VND	1 Piece(s)	Available	Same day	12	12	32	41	3.01~5.00	4	0.15	0.5 / +0.5/-0.5	1.6 x 10^-5	-
330,981 VND	1 Piece(s)	Available	Same day	12	14	32	41	3.01~5.00	4	0.15	0.5 / +0.5/-0.5	1.6 x 10^-5	-

Loading...Tải…

Product TOP

Basic InformationThông tin cơ bản

Application	For Servo Motors / Stepping Motor	Features	Zero Backlash / Low Moment of Inertia	Allowable Misalignment	Angular Misalignment / Eccentricity / Axial Misalignment
Max. Rotational Speed Range(r/min)	4001~10000	Body Material	Aluminum Alloy	Allowable Angular Misalignment(deg)	2
Product Category	Coupling Main Body	Allowable Lateral Misalignment Range(mm)	0.02~0.2	Max. Rotational Speed(r/min)	10000
Disc Material	Stainless Steel	Standard/Short	Standard Type	Shaft Bore Shape	Standard Bore
Shaft Tightening Method	Set Screw

The specifications and dimensions of some parts may not be fully covered. For exact details, refer toCác thông số kỹ thuật và kích thước của mã sản phẩm có thể không được bao phủ đầy đủ. Để biết chi tiết chính xác, hãy tham khảo manufacturer catalogsdanh mục nhà sản xuất ..

Frequently asked question (FAQ)FAQ

Question:Question: What is a coupling?: Answer:Answer: A coupling is a part that connects two different rotating bodies (motor shaft, ball screw, etc.) and aims at transmitting torque. The load of assembly adjustment is reduced by absorbing the axis deviation (lateral misalignment, angular misalignment and axial amplitude) between rotating bodies. And in case of accidental overload, the coupling is destroyed and the rotating bodies are disconnected to protect the expensive power part and the whole device.
Question:Question: What are the types of MISUMI couplings?: Answer:Answer: There are disc type, grooved type, cross type, claw type, bellows type, rigid type and universal joint type.
Question:Question: How to select coupling according to motor?: Answer:Answer: Disc type is recommended for servo motors, grooved type is recommended for stepping motors, and cross type is recommended for universal motors.
Question:Question: How to select according to the purpose, environment, working conditions?: Answer:Answer: Please refer to the MISUMI website.
Question:Question: What kind of coupling should be used when the angular misalignment is very large?: Answer:Answer: Please select the universal joint with allowable angular misalignment of 30 degrees. In addition, when grease cannot be applied regularly, use a rubber sleeve to fill grease and use it.
Question:Question: Which disc type coupling is better, single disc type or double disc type?: Answer:Answer: Double disc type can absorb angular misalignment and lateral misalignment, but the total length will increase.
Although the total length of the single disc type is short, it is only suitable for applications with narrow space because lateral misalignment is not allowed in the structure. Special attention should be paid to centering during use.
Question:Question: How much is appropriate to insert the shaft into the coupling during installation?: Answer:Answer: Please select the length of the main body (coupling part) described in the product catalog. If the insertion amount is too short, the shaft may slip and the clamping part may be damaged; If the insertion amount is too long, it will be damaged due to shaft interference inside the coupling.
Question:Question: Why is it necessary to install a protection cover around the coupling?: Answer:Answer: Due to high-speed rotation, accidental contact may result in injury or entanglement of gloves, towels, etc. In addition, for some reasons, parts may be damaged or debris may be scattered. Therefore, be sure to install the safety protection cover.
Question:Question: What should I do if there is no matching shaft bore diameter?: Answer:Answer: Please select a product with changeable keyway width or available with keyway processing. MISUMI products are divided into MCSLCWK series (disc type), CPOC series (cross type) and MMJN series (claw type), etc.
Question:Question: Is it a defective product that has difference in groove gap width?: Answer:Answer: Since the difference is within the dimensional tolerance range, there is no problem.

Check other FAQ (7 items) HideĐóng.

MISUMI Unit Example related to this product

back next

Top of the page

About MISUMIVề Misumi

About this WebsiteVề trang Web này

Useful ToolsCác công cụ hữu ích

Customer ServiceDịch vụ chăm sóc khách hàng

MISUMI Contact Monday to Saturday: 8:00 am - 5:00 pm Order cut off time is 5:00 pm Thứ 2 đến Thứ 7: 8 giờ sáng đến 5 giờ chiều Hạn chót đặt hàng là 5 giờ chiều

Tel:Số điện thoại:0222-361-1555
Fax:Số Fax:0222-361-2555
InquiryYêu cầu

MISUMI APP

Install MISUMI APP

MISUMI Vietnam Company Limited, Legal Representative: Tomohiro Watanabe,
phone: 0222-361-1555, e-mail: cs@misumi.com.vn, Enterprise Code: 0107514576,
Date of Issuance: 22 July 2016, Place of Issuance: Bac Ninh, Business Certificate No. 6573041568-KD dated 27 September 2016 issued by the People's Committee of Bac Ninh

Công ty TNHH MISUMI Việt Nam, Đại diện theo pháp luật: Tomohiro Watanabe,
Điện thoại: 0222-361-1555, e-mail: cs@misumi.com.vn, Mã số doanh nghiệp: 0107514576,
ngày cấp 22/7/2016, nơi cấp: Bắc Ninh, Giấy phép kinh doanh số: 6573041568-KD ngày cấp 27/9/2016 bởi UBND tỉnh Bắc Ninh

How can we improve?

ConfigureTạo

Specification/DimensionsĐặc điểm kỹ thuật / Kích thướcĐặc điểm kỹ thuật / Kích thước

Shaft Bore Dia. 1 d1 (or d)(Ø)

Shaft Bore Dia. 2 d2 (or d)(Ø)

O.D.(Ø)

Overall Length(mm)

Allowable Torque Range(N•m)

Allowable Torque(N•m)

Allowable Lateral Misalignment(mm)

Shaft Tightening Method

type

CADCAD

Days to ShipSố ngày giao hàng

Specify AlterationsChỉ định thay đổi

Slit Couplings Long, Set Screw Type

Copy Part Number URL to Clipboard

(i) Caution thận trọng

Product Description

Economy Long Slit Coupling - Set Screw Type

Coupling Product Overview

Coupling Product Feature

Dimensional Coupling Drawing

Coupling Specification Table

Coupling Precautions

Example of Use coupling

Coupling Usage Method

Part Number

Basic InformationThông tin cơ bản

Frequently asked question (FAQ)FAQ

MISUMI Unit Example related to this product

About MISUMIVề Misumi

About this WebsiteVề trang Web này

Useful ToolsCác công cụ hữu ích

Customer ServiceDịch vụ chăm sóc khách hàng

MISUMI Contact Monday to Saturday: 8:00 am - 5:00 pm Order cut off time is 5:00 pm Thứ 2 đến Thứ 7: 8 giờ sáng đến 5 giờ chiều Hạn chót đặt hàng là 5 giờ chiều

(i)
Caution

thận trọng